Replacing the fork seals or dust seals on an R1150 is pretty easy, and should only take 10-15 minutes. This is how I did it on my 2001 BMW R1150GS without removing the front wheel or forks from the motorcycle.
Tools I used:
- flat blade screwdriver
- 22mm wrench
- 3/8” socket wrench
- 14mm socket
- needle nose pliers
- seal puller (seriously recommended, but not required)
- hammer
- socket to pound oil seal in. I used a 3/4” to 1” impact adapter. I’ve read about a 1 3/8” socket fitting too.
- 3mm allen wrench
- includes affiliate links to support the blog
The new dust seals on the left and the oil seals on the right. I paid about $15 for each seal on bikebandit.com.
This is the order of all the parts in the fork tube on the bottom, left to right: washer, oil seal, retaining clip, dust seal, *not shown fork nut 14mm*, fork cap
1) put the bike on the center stand to make the front wheel easy to move around.
2) Remove the re-usable ziptie holding the brake or clutch cable depending on which side.
Press the tab back towards it to pull it apart.
3) Remove the cap on the top of the fork with the flat blade screwdriver by inserting it into the slot
4) Using the 14mm socket and 22mm wrench, remove the nut on the top of the fork tube. I used a 7/8” as shown below.
5) Push the fork slider into the stanchion and then pull it out. The front wheel will freely move side to side to make this very easy.
Have a rag handy as the slider will likely drip fork oil as you pull it out. Wipe it clean, and set it aside in a safe place where it won’t be scratched.
6) Use the flat blade screwdriver again and remove the dust seal on the top of the stanchion.
Both of mine were split and cracked (and leaking). I’d recommend replacing them along with the oil seals.
8) With the needle nose pliers, pull out the retaining clip
9) With the seal puller, remove the oil seal.
If you don’t have a seal puller, get one. It makes this part take five seconds (literally) with no damage to the fork tube versus trying to lever (and bend) with a screwdriver or something else. I bent two different screwdrivers, but didn't get the seal out. I've also read you could screw wood-screws into the bad seal and pull it out with a pliers. The seal puller did the job for me.
the leaky oil seal aka fork seal
position under the fork seal
pull up slightly and it will pop right out
remove the seal
the damage to mine is clear here:
new fork seal aka oil seal below:
this is the top view:
this is the bottom view:
10) seat the new seal with a socket. A little fork oil on the seal makes it easy to start by hand. Make sure to insert it with the bottom side down.
Get a socket that is the same diameter as the outside of the oil seal, and that fits inside of the tube. You want to push on the hard outside, not the soft inside of the seal. I used a 3/4” to 1” impact adapter I found at harbor freight. A 34mm or 1 3/8” socket might also work.
Put an extension on it and pound it home.
11) reinstall the retaining clip
12) install the new dust seal by pressing it into place
13) use the 3mm allen wrench and remove the little bleed screw near top of the fork slider
be careful not to lose or damage the tiny o-ring
14) push the slider all the way into the fork tube and then pull it back up to the top yolk in its final position. Air should rush out the bleed hole. I repeated this twice.
15) replace the bleed screw and hand tighten until snug. This is a small screw, so be careful not to over tighten.
16) Replace the nut. Using the 14mm socket and 22mm wrench tighten. If using a torque wrench, tighten to 45Nm.
17) Replace the top cap and re-usable ziptie.
18) Repeat on the other side.
19) Go for a ride!
If you want to also replace the fork oil, use BMW fork oil grade 7.5 and put 15.8 oz. of fluid in each fork.
Other R1150GS Guides:
Good write-up and description of the process. I have been procrastinating on my old bike. It is also a pretty quick process but the wheel and fender needs to be removed. How often should the fork oil be replaced?
ReplyDeleteRichardM: Thanks! Good question too. My haynes manual said to remove the front wheel and such, but it seemed like way too much work. (especially after the above method)
ReplyDeleteMy manuals don't mention an interval for fork oil changing on the BMW, and I don't see it on any maintenance schedule online. I'm guessing since mine is a telelever setup and the forks don't actually do anything other than assist steering, the oil isn't as important as in other bikes.
For other motorcycles with normal forks, a quick search on the internet seems to be every other year.
Nice job Chris, it really does look pretty easy.
ReplyDeleteAs to how often, I dimly recall my beemer mechanic saying something like at every major service, which is every 10K miles.
dom
Redleg's Rides
Colorado Motorcycle Travel Examiner
Dom: Thanks. It is easy and fork oil is cheap. Now if only all my bikes used the same weight!
ReplyDeleteChris: Great post, best set of nstructions I found anywhere. very detailed and photos are the best. Couldnt have done without them.
ReplyDeleteWas able to do seal replacenment without taking the wheel/fender off.
All other instructions are great too. Thanks a lot for posting them.
One addition will be helpful - what' the oil level supposed to be? Mine was leaking for sometime so I thought I would add some oil but didnt know how much. I must hav added a little too much because when I inserted the tube and moved it up and down a couple of times as suggested, oil squirted out from the top screw hole. Big mess, Lesson learned!
Thanks! I'm glad you found it useful. I like to write them in the way I'd like to use them. :)
Delete15.8oz in each fork is the recommended amount from BMW. See the very last photo.
Thank you for these instructions. I modified them for the insertion of the new seal. I tried and ruined a seal using a socket to drive the seal in. Just was not able to keep the socket/seal square. Instead I wrapped the slider with electrical tape with nearly the same thickness as the seal. Then I used the slider with electrical tape to drive seal home.
ReplyDeleteGlad you were able to make it work. The socket must just barely fit to work as a driver. Rode safe!
ReplyDeletemate thank you for this write-up. it will help me immensely as I just bought an R1150GSA and the forks are leaking. thanks!
ReplyDeleteR1150GS - 2001. My left fork seal has been leaking for a while. I will need to add/change the fork oil. At what point in these steps would I suction out the old oil replace with new? Is there a recommended or specific process to drain and add? I would prefer to not remove the wheel and fork.
ReplyDeleteI would add fluid between step 9 and 10 after you get the old seal out and before the new seal goes in.
DeleteThanks Chris.
DeleteHave a 02 GS and use your advise often to work on her. She has been a great bike coming up on 80000 miles. Have had her since 2012. One of my regular riders. Thanks for all the info
ReplyDeleteI have spent hours looking for info on the air bleed component, neither the Haynes manual nor the BMW service manual describes it and nor do any of the current youtube videos. Everything else is pretty simple but the bleed bit had me stumped. Presumably you need to bleed the tube so the oil/lubrication circulation works under a slight vacuum? Thanks and regards Tim
ReplyDelete